Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - doug

Pages: 1 ... 3 4 [5] 6 7 ... 22
61
User Projects & Pictures / Re: Please help me design this oil stove.
« on: February 12, 2016, 03:07:09 pm »
I stand corrected.
https://www.youtube.com/watch?v=3wpTWcPRNH4
https://www.youtube.com/watch?v=cYxtNRKj1Es&list=PLuex1gs8VmeOv6Pk-BAyxh0iuRzBWzPyT
I knew the men had a center air supply.

62
User Projects & Pictures / Re: Please help me design this oil stove.
« on: February 10, 2016, 07:15:34 pm »
I believe your burner needs to be on the outside of the stove to work correctly.  If the burner is on the inside of the stove where is the burner getting it's oxygen to burn the fuel?

63
User Projects & Pictures / Re: Please help me design this oil stove.
« on: February 07, 2016, 04:03:37 pm »
Looking forward to seeing your Ozzirt burner build. Hope you post lots of pic and give a lot of details.

64
Waste Motor Oil / Re: Tank outside, cold affecting psi?
« on: January 02, 2016, 07:25:50 pm »
what regulates your pump? how do you know the oil volume/pressure at the burner. if you look down on the red tank the gray box is a metering pump. I believe it's needed to be used with your burner.

65
Waste Motor Oil / Re: Tank outside, cold affecting psi?
« on: January 02, 2016, 06:07:09 pm »
http://www.centralohioheaters.com/DSCN9645.JPG

does your heater look like this? where is your pump located?

66
User Projects & Pictures / Re: my project
« on: December 03, 2015, 06:27:49 pm »
I like your burner. Could you tell us more about it and how it works.

67
Fuel Oil Boilers / Re: Waste oil boiler-design and where to start
« on: November 30, 2015, 05:10:59 pm »
heat exchanger, aqua-stat, expansion, a couple air bleeders, and pump I have two ball valve  for water lines in and up. water supply for closed loop system you'll need water valve, check valve, pressure valve. does your boiler have a pressure release valve?

are you planning heating your domestic hot water?

what kind of boiler did you buy?

welcome to the site.

68
Fuel Oil Boilers / Re: Waste oil boiler-design and where to start
« on: November 29, 2015, 06:31:42 pm »
my local plumbing shop helped me with the closed system, expansion tank, air bleeders, aqua-stat. most of the other stuff is from outdoor wood boiler set ups. pumps, mixer valves thermostat control.

69
Fuel Oil Furnaces / Re: Need help with a new to me waste oil rig
« on: October 30, 2015, 09:14:08 pm »
Your welcome. Maybe down the road you can return the favor to some else with burner problems. In the last five years I've had a lot of help from a lot of people. That's why we're here, it's to help each other. I just don't stop in here as much as I use to. Glad you have your burner running.

70
Fuel Oil Furnaces / Re: Need help with a new to me waste oil rig
« on: October 28, 2015, 07:38:21 pm »
I would replace the CAD sensor with the correct part. Sounds like the primary safety is not getting the proper signal from the CAD sensor and shutting the burner off.

71
Fuel Oil Furnaces / Re: Need help with a new to me waste oil rig
« on: October 27, 2015, 06:47:33 pm »
Was your burner trying to fire for 30 seconds or did you have a flame for 30 seconds?

72
Fuel Oil Furnaces / Re: Need help with a new to me waste oil rig
« on: October 23, 2015, 03:27:58 pm »
Welcome to the forum. I'd try looking at Granger first. http://www.grainger.com/content/general-catalog
Or at Centralohioheaters. http://www.centralohioheaters.com/All-other-brands.html
Got any more pic of your burner?

73
User Projects & Pictures / Re: 600Kw output Drip fed burner.
« on: May 01, 2015, 08:25:53 pm »
What ya going to do with all that heat?

74
Waste Motor Oil / Re: let the fun begin
« on: May 01, 2015, 08:16:37 pm »
Russ,
It's getting tougher to find the volume of waste oil that I use. The fuel oil will help me get a head on the amount waste oil I'll have on hand. Burners got 11,000 hours and has been clicking them off with no problems.

75
Waste Motor Oil / Re: let the fun begin
« on: April 28, 2015, 09:19:02 pm »
Get your free heat where ever you can. Scored 550 gallons of free fuel oil this weekend. All I had to do was pump it from their tank. Looks like some of next season we'll be heating with fuel oil.

Pages: 1 ... 3 4 [5] 6 7 ... 22