Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dannyo

Pages: [1] 2
1
Welcome Center / Re: Clean burn won't light
« on: January 03, 2021, 05:53:32 am »
I really appreciate your help. If there is any thing I can do in the future let me know. I have a fair amount of experience with autos and trucks. Again thanks.

2
Welcome Center / Re: Clean burn won't light
« on: January 02, 2021, 06:05:39 am »
Houston we have lift off. It fired up and leveled off after excess oil burnt off.
I assume the electrode was the issue.
Any advice setting the combustion air or air pressure?

3
Welcome Center / Re: Clean burn won't light
« on: January 01, 2021, 07:31:10 am »
Ok thanks
If I want to check the oil mist or stream can I do it with jumpers like the electrode?

4
Welcome Center / Re: Clean burn won't light
« on: December 31, 2020, 06:13:18 am »
575’

5
Welcome Center / Re: Clean burn won't light
« on: December 30, 2020, 06:31:38 pm »
It only has one for air.

6
Welcome Center / Re: Clean burn won't light
« on: December 30, 2020, 02:38:24 pm »
Replaced the electrode and set, good spark.
The furnace is trying to fire, a lot of smoke. Won't light.
Oil pressure is 3.5, calls for 1.5 to 2.
I'm not aware of an adjustment for this.
Could there be trash or restriction causing an increase in pressure?
How is the pressure regulated?

7
Welcome Center / Re: Clean burn won't light
« on: December 30, 2020, 10:51:11 am »
I have ordered an electrode it should be here today. The nozzle is clean.
When I get the electrode I will adjust the air and see what happens.
I will get back to you Thanks

8
Welcome Center / Re: Clean burn won't light
« on: December 30, 2020, 05:35:42 am »
Motor is running
I adjusted the electrodes per Cleanburn manual
The arc does not seem to be at the tips

9
Welcome Center / Re: Clean burn won't light
« on: December 29, 2020, 03:58:45 pm »
Its more over the top of the nozzle.

10
Welcome Center / Re: Clean burn won't light
« on: December 29, 2020, 09:40:10 am »
There is a spark on the electrodes and the motor runs.

11
Welcome Center / Re: Clean burn won't light
« on: December 28, 2020, 04:03:08 pm »
The burner swings out. If I lift up the ignitor i can attach the lead to the electrode.
This is where Im sure of myself. Is one side hot and the other ground?
If not please educate me.

12
Welcome Center / Re: Clean burn won't light
« on: December 28, 2020, 05:46:41 am »
No spark apparent with mirror.
If I’m getting 120 v on blue ,spark on igniter to electrode, could the electrode be bad?

13
Welcome Center / Re: Clean burn won't light
« on: December 27, 2020, 09:12:21 am »
What does the Cad Cell do?

14
Welcome Center / Re: Clean burn won't light
« on: December 26, 2020, 12:48:20 pm »
It was running, then quit and wouldn't restart.
I'll try the mirror. Thanks

15
Welcome Center / Re: Clean burn won't light
« on: December 26, 2020, 10:05:47 am »
Blue is 122 v when starting. I checked and adjusted the distance on the electrodes to nozzle and between.
Lifting ignitor there is an arc.
Should the white wire be 120v from ignitor when trying to fire?
Oil pressure is 3.25 psi / Air is 15 psi
it calls for 1.5 to 2.0 for oil psi.
Will the high oil pressure create this situation?



Pages: [1] 2