Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Russ

Pages: 1 ... 25 26 [27] 28 29 ... 37
391
Board Suggestions / Site not loading correctly in FireFox
« on: October 30, 2011, 11:13:29 am »
Anyone else having trouble loading this site in FireFox? 

Internet explorer seems to work fine for me, so I am thinking it is a FireFox problem.

How has it been working for the rest of you?

392
Waste Motor Oil / What do recyclers do with waste oil?
« on: October 30, 2011, 11:12:08 am »
Does anyone know what happens to oil that gets recycled at the public dump spots or the stuff that in & out oil change stations recycle?

I have never seen a bottle of new oil that says "made from 25% recycled oil".  I wonder if it gets turned into other tyeps of lubricants, or does it get burned somewhere?

393
Welcome Center / Re: Hello from Idaho
« on: October 30, 2011, 11:06:10 am »
Looking good!  That looks like quite a setup.  Getting things perfected is always a little tricky, but when they work good, lots of heat!

Enjoy the forum and hope to see more about your heater.

394
Waste Motor Oil / Re: Ash Disposal
« on: October 25, 2011, 09:43:26 pm »
Good question.  If you end up finding any official information on disposing of ash, or even for burning waste oil, we should make it a sticky topic on the forum. 

395
Waste Motor Oil / Re: industrial oils
« on: October 25, 2011, 09:38:10 pm »
Hi Matthew,

From other reading I have done, hydraulic oil and transmission fluid seem to work fine.  I think I remember hearing that transmission fluid burns a little hotter.  I havent had experience with it myself, just from reading.  Maybe others have burned it themselves and can share what they know.

Good luck with the burner!

396
Waste Motor Oil / Re: let the fun begin
« on: October 21, 2011, 10:54:10 pm »
Sounds good doug.  I would love to find a boiler myself.  Keeping an eye on craigslist this winter.  They dont show up too often though.

397
Waste Motor Oil / Re: Ash Disposal
« on: October 21, 2011, 10:53:00 pm »
Probably just a dead form.  It gets a little more active as the winter goes on, so keep checking back, maybe someone will reply. 

If I were to dispose of mine, I would put it in the garbage.  The garbage ends up in the incinerator.  So it would get burnt again.  Kind of re-fried beans...HA!

398
Waste Motor Oil / Re: Out of oil for the season?
« on: October 19, 2011, 05:05:40 pm »
Sounds like you have yourself a good supply saved up.  I was just thinking of firing mine up to make sure everything works before it gets too cold out in the shed.

Good luck getting it tuned up and stay warm...


399
Drip System / Re: old german drip system, need grates, advice
« on: October 15, 2011, 07:49:55 pm »
Greetings Stubborn66,

I think most are working with home made units, or modified residential systems, but maybe as it cools down and the board becomes a little more active, someone will have some ideas for you.

Good luck with your heater!


400
Waste Motor Oil / Re: Sky waste oil burner
« on: October 03, 2011, 08:32:02 pm »
Hello,

Does your waste oil burner have a heating mechanism to heat the oil?  If so, is it running at the proper temp? 

Not sure about the design of your heater, but I would check there first.

Good luck in finding the trouble...

Russ

401
Welcome Center / Re: Hello from Australia!
« on: September 26, 2011, 08:00:21 pm »
Welcome to the forum.  We are glad you found us!

Your heater sounds interesting.  Glad to hear it works well for you.  If you get a chance, snap a picture and post it up for us to see.

There are a lot of ideas out here and things should start getting busier as it gets colder here.

Best of luck with your heater!

402
Compressed Air Sources / Re: refrigerator type compressor
« on: September 19, 2011, 09:24:51 pm »
Hmm... interesting.  Could these be used to transfer oil?  For example from my 55 gallon drum to a 5 gallon bucket?  I am not concerned about speed, but how many gallons per minute would one pump?  Are they self priming?

Thanks for the info.

Russ

403
User Projects & Pictures / Re: Finally a working waste oil heater
« on: August 23, 2011, 04:53:42 pm »
Greetings and thanks for sharing!  Nice job on the heater.

I'm not sure on how the turk works.  Is that a pump on the top of your oil storage tank?  I see a fan, what is that for?  I also see one of the pictures that has a computer power supply.  What is that used for?

Looking forward to learn more.

Thanks!

Russ

404
Welcome Center / Re: Burner Problems
« on: August 23, 2011, 04:50:05 pm »
Greetings and welcome to the forum.  Things might be a little slow out here until the heating season is upon us, but maybe somebody will chime in and have some suggestions for you.

Does your burner have a nozzle heater on it?  My burner will flutter if the temp isnt high enough.  I couldnt figure out what was going on with it at first, but after some experimenting I found that the oil temp was not high enough.  I raised it and got a nice stead burn.

Good luck with your troubleshooting.

Russ

405
User Projects & Pictures / Re: my selfbuilt waste oil boiler
« on: May 03, 2011, 10:29:35 pm »
Very nice videos.  Thanks for sharing!  Thats quite a project, good job.  What kind of pump do you use to circulate the water?

Pages: 1 ... 25 26 [27] 28 29 ... 37