Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - doug

Pages: [1] 2 3 ... 22
Waste Motor Oil / Re: Wanting to make an efficient burner
« on: November 04, 2020, 08:11:30 pm »
 I too have not run this style burner. What I have seen in this style burner is less and smaller diameter holes in the primary burner. Also I have never seen this large of diameter holes in the secondary burner.

 I found this video that may help.

Waste Motor Oil / Re: CK burner & Buderus boiler Video
« on: November 04, 2020, 07:59:38 pm »
  Like your set and enjoyed the video.

Waste Motor Oil / Re: homemade WMO conversion for wood stove
« on: February 18, 2020, 06:41:35 pm »
  Can you link us to that youtube  video

Waste Motor Oil / Re: CK burner kit
« on: February 16, 2020, 06:04:55 pm »
  I too like dealing with Craig. Always quick to respond and always helpful.

Welcome Center / Re: Another Newbee
« on: October 04, 2019, 08:10:48 pm »
I use a metering pump with a siphon nozzle. I don't like the idea of a float tank either.

Welcome Center / Re: Hello and thank you for letting me join!
« on: March 29, 2018, 06:49:52 pm »
  40' x 70' with 16' ceilings is no small building. The wall I see is not insulated. Who knows if the ceiling and other walls are insulated. The heater sets in a corner of the building and don't forget about the 3 overhead doors. Maybe 1600 gallons is about right.

Waste Motor Oil / Re: New and have questions!
« on: March 16, 2018, 06:50:14 pm »
 I don't see where using no electric is a problem. There's a lot of drip heater that don't use power.

 Are you wanting to build a heater similar to this style?

Welcome Center / Re: Glad I found this place
« on: March 16, 2018, 08:54:44 am »
 I don't know the proper term for it, but I just click on the "image.jpg" next to the paper clip and it show the pic very well.

Welcome Center / Re: Glad I found this place
« on: March 14, 2018, 08:23:42 pm »
 Can you tell us more about your burner/gun?

Waste Motor Oil / Re: Waste Oil Boiler install
« on: March 07, 2018, 11:14:51 am »
  I don't get any carbon build up in my set up. It does create ash build up. I just vacuum it out.

Waste Motor Oil / Re: Transfer Pumps?
« on: February 17, 2018, 02:45:14 pm »

 I don't live in a frozen hell hole where I have to worry! :0)

  Ouch! It's not that bad here. It still get mighty cold at times. I'm sure the pump will hold up. Just looking for someone that has experience moving waste motor oil at or below freezing temps. Looking to find out what ac motor they're using. I don't want to go overboard on an ac motor. Someone here suggested a lower rpm motor. 2hp sounds a little large. What do I know? Thanks for the help.

Waste Motor Oil / Re: Transfer Pumps?
« on: February 07, 2018, 07:36:45 pm »
    Hey Oilburner,  I have watch your videos a lot.
 How does your 1/3hp 2800rpm ac motor handle waste motor oil at freezing temps and below?

Waste Motor Oil / Re: solid state relay
« on: January 30, 2018, 08:43:03 am »
I see these ss relays mounted on heat sinks. Would I need to use a heat sink or mount it where my old relay had been?

Waste Motor Oil / Re: solid state relay
« on: January 25, 2018, 07:09:25 pm »
Russ, Thanks for the info.

Waste Motor Oil / Re: solid state relay
« on: January 24, 2018, 05:24:32 pm »
Hey Russ,
 The relay is 120vac. It's the relay that operators the 500w heater cartridge in the preheater block that is activated from the PID heater controller.

Pages: [1] 2 3 ... 22