Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - steve

Pages: [1]
1
Waste Motor Oil / Re: Waste Oil Burner Prices
« on: January 02, 2013, 09:43:56 pm »
pls put me on your list also. i would like to try 1 of your compresors , im using a small gast medical comp now works great but one right on the burner would clean things up, im running a CK burner, in a vericial boiler, works great. thanks Steve

2
Welcome Center / Re: Hello From Thermopool Ltd, just joined this forum
« on: February 26, 2012, 09:24:59 am »
what is a heater around 250,000 btu worth ?

3
Temp Controllers and Thermocouples / Re: Can you use a Ranco temp controller?
« on: February 25, 2012, 10:41:48 pm »
hi, i dont think a ranco will work cause when you power it up it sends power to the source untill it reches the desired temp you have programed so when the gun fires you could be down in temp and it wont fire, unless you leave the ranco on a seprate circuit so its heating the block all the time even when the gun isnt running, i would just worry that the oil will clog your gunver time

4
Welcome Center / Re: converting a fuel oil furnace to bi fuel
« on: November 14, 2011, 08:39:31 pm »
Hey Nascar
take a look at ckburners.com  this system works awesome im running 1 now for a year now, i have tried what you are thinking of doing it dint work for me also the nozzels plug very easy.

5
Waste Motor Oil / Re: let the fun begin
« on: October 26, 2011, 11:35:53 pm »
i wonder if it has somthing to do with the position of my retension head, what temp are you running on your PiD

6
Waste Motor Oil / Re: let the fun begin
« on: October 26, 2011, 08:41:00 am »
Hi  Doug
i also am running a Ck burner assembly it works great. but i do have a carbon problem between the electrodes
causing a bridge, then it wont fire.  it doesnt happen often, have you run in to this problem, other than that it burns clean and put out a pile of heat.

7
Compressed Air Sources / Re: refrigerator type compressor
« on: September 12, 2011, 11:52:37 pm »
these fridge compessors work awsome; im running a old one and it runs my sypon  nozzel burner. they work good.

8
User Projects & Pictures / Re: Finally a working waste oil heater
« on: September 12, 2011, 11:48:02 pm »
hEY Russ
lookes like a 12 volt pump thats what the power supply is for; im not sure how this oil burner goes toghther need more info and pics

9
Welcome Center / Re: another newbie
« on: February 19, 2011, 09:29:16 pm »
Hey Farmer,
why dont you post some pic of your furnace, this site has been dead latley, i check ever day but nothing new !
im workin on a pressure system, i will post pics when it up and running, thanks Steve

10
Pressure Nozzle / Re: Kyle's wmo pressure system
« on: February 14, 2011, 08:32:01 pm »
HEY NIK,
THIS SYSTEM HE IS USING THE PUMP,SO PRESSURE SYSTEM . I NOTICED NOBODY ANSWERED YOU.

11
User Projects & Pictures / Re: Dead Eye Lil Gun
« on: February 13, 2011, 11:59:11 am »
Thanks Dead Eye,  i ordered a pre heater block and nozzel from ck burners,also a pid and retension head, how did you make out with yours is it up and running now ?

12
User Projects & Pictures / Re: Dead Eye Lil Gun
« on: February 02, 2011, 10:17:20 pm »
Hi Dead Eye

do you have any pics of the nozzel your using, im kinda lost how this sypon system works, or is there any detailed pic on this website  Thanks Steve

13
User Projects & Pictures / Re: My beckett pressure burner learn with me as I go!
« on: February 02, 2011, 10:04:06 pm »
HI Andy,
first of all thanks for all the info and pics. im builing the same system as you except im using deisel to fire and heat the fire box up then switching to wmo, im doing this manually at this point till i get some bugs out, then with electic valves and a timer on the deiesel, i figure it woulnt burn much deisel at all, its just enough to get things hot. to acheive a good burn with the oil, what are your thoughts on this being your a electician. thanks steve.

Pages: [1]